Welcome to the Ness forum: identifying DPlus, D8x/D16x, M1 and SmartLiving panels

Discuss Ness Alarm Systems, Including Smart Home Integrations
Post Reply
User avatar
ZerOne
Site Admin
Posts: 292
Joined: Sun Dec 13, 2020 8:21 am

What this thread is
A starter map of Ness Corporation alarm panels you are likely to meet in Australian homes and small sites, and how to tell which one you have. It is written for homeowners, integrators and licensed installers. Companion threads in this forum cover Home Assistant integration, installer programming basics, and apps, remote access and monitoring.

It is not official Ness advice, not a substitute for the installer manual for your exact board and firmware, and not a product endorsement. Ness updates firmware, kit contents and which SKUs are stocked; if a fact matters for a live panel, confirm it against the current manual or with Ness technical support. I have not bench-tested these combinations.

Complexity
Reading: beginner. Opening a live panel, changing programming, or installing security equipment in Australia is a different matter — see who needs a licence to install alarms, CCTV or access control and Australian electrical compliance for smart-home work.

1. Who Ness is
Ness Corporation Pty Ltd (ABN 28 069 984 372) is an Australian designer and manufacturer of alarm systems and detectors, and a supplier of related security products. The about us page says the company was co-founded in 1972, is headquartered at Seven Hills in Sydney, and has sales branches in Sydney, Melbourne, Brisbane, Adelaide and Perth. National technical support is listed as 1300 551 991 and techsupport@ness.com.au.

Ness sells primarily to the trade (a trade web account and the five capital-city branches). Homeowners usually obtain equipment and programming through a licensed installer, not by treating ness.com.au as a retail shopfront.

2. The current D-series platform: DPlus
Ness's current D-series platform, still being promoted in a brochure dated 2026, is DPlus — described as "continuing the evolution of Ness D-series". The official DPlus brochure v3 and the Installation & Programming Manual, document 890-511, Rev 1.12 (October 2024) (for firmware V12.0 and later) are the documents to start with.

In outline, as those documents describe it:
  • The base panel is 8 hardwired zones (part 106-981-P in the brochure shopping list), with no zone-doubling on the expanders used to grow the system.
  • Local expanders: DPlus-L16 (zones 9–16) or DPlus-L24 (zones 9–24) at the main board.
  • A DPlus-R16 16-zone remote expander kit builds a decentralised 32 hardwired-zone system (16 local + 16 remote).
  • With an optional radio interface, the panel also supports up to 32 wireless zones. Wireless zone numbers are shared with hardwired zone numbers (for example, hardwired zones 1–8 share numbers with radio zones 1–8). You can have a hardwired device and a wireless device on the same zone number. The zone map is still 1–32.
  • Optional 4G (part 106-985 in the installer manual) and ethernet / app via Ness-Bridge Plus (106-018) or the earlier Ness-Bridge (106-014).
  • Onboard 3-door access control (Wiegand readers with the optional interface).
  • Keypad options include the Navigator touch screen (106-101 Gen2), KPX+ (106-310) and Saturn+ (white / ocean mist / black). The installer manual says DPlus needs KPX/Saturn keypads Rev 2.0 or later, or a Navigator Rev 4.0 or later.
  • Up to 56 user codes (keypad PIN, radio key or access card) and two-area partitioning plus a common area, in the same family as earlier D-series panels.
  • Programming by keypad, by NessComms (V6.00 or later for DPlus, via the serial port), or by SMS if the optional 4G module is fitted.
3. D8x / D16x Deluxe, and D8XCEL / D16XCEL 4G
These are the panels you will still find in a great many existing Australian installations, and some SKUs remain in the Ness catalogue.

D8xD / D16xD Deluxe (8 or 16 hardwired zones) is documented in document 890-017, Rev 2.5D, August 2024, for Deluxe firmware V8.0 and later. That manual can also be used with earlier D8x/D16x panels, but some options exist only on V8.0+. For V7.8 and earlier, Ness points to manual 890-007. Deluxe features called out on the manual cover include expanded AUX outputs (up to 8), voice alarms and prompts, an enhanced modem, a real-time clock, optional radio, onboard access control, and optional C-Bus connection via Ness MiniCENTRAL. Typical keypad choices are the same Navigator, Saturn and KPX family. Up to three mixed keypads, or four Navigator keypads.

D8XCEL 4G / D16XCEL 4G are 8- or 16-zone panels with a 4G communicator onboard and a Ness SIM supplied (activate the Ness plan or bring your own). The XCEL installer manual, document 890-490, Rev 1.14, February 2024 covers firmware V11.3 and later. Central-station reporting is in ArmorIP and Contact ID formats; Ness has since published a strong advisory against relying on Contact ID over the 4G voice path — that belongs in the monitoring thread, not here. As at 22 November 2026, the D16XCEL "panel only" listing was still on ness.com.au, while the D8XCEL "panel only" SKU 106-450 was marked no longer available. Other XCEL kits were still listed. Treat current stock as something to confirm with Ness; DPlus is the platform Ness is actively presenting as the D-series successor.

A practical identification detail from the manuals: DPlus, XCEL, and D8x/D16x V8 and later use the 4-pin serial cable 450-246. Earlier D8x/D16x use the 3-pin serial cable 450-185. That is often enough, with the board label, to separate an older D8x/D16x from a later board when the housing sticker is missing.

4. Ness M1 Gold — a different platform
The Ness M1 Gold is still listed by Ness as a kit (control module, 14-inch housing, power assembly and battery). The official installer manual is titled for the NESS ELK-M1G and ELK-M1 controls. In plain language: this is the Elk M1 Gold platform, sold and supported in Australia by Ness, not a D8x-style panel.

As the M1 Gold control module page describes it, the board has 16 zones onboard, expandable to 208 with input expanders on the four-wire data bus, up to 8 areas, 199 user codes, a voice announcement vocabulary, an onboard telephone dialler and optional ethernet ("virtual keypad") and access-control accessories. Programming is a different tool chain (Ness-RP / Elk-style software), and the official Home Assistant ness_alarm integration does not apply to M1. If your keypad or board says M1, start from the M1 manual, not from a D8x guide.

5. Ness SmartLiving — another different platform
Ness still lists SmartLiving panels. The SmartLiving brochure describes four versions, all in metal enclosures:
  • SmartLiving 505 — 5 terminals on the board (10 zones); no further zone expansion on that model
  • SmartLiving 515 — 5 terminals (10 zones) on the board, expandable to 15 terminals / 30 zones
  • SmartLiving 1050L — 10 terminals (20 zones), expandable to 50 terminals / 100 zones
  • SmartLiving 10100L — 10 terminals (20 zones), expandable to 100 terminals / 200 zones
The platform uses Ness's I-BUS, optional Air2 two-way wireless, Alien / nCode keypads, optional SmartLAN IP boards, optional Nexus GSM, and SmartLeague PC software. It is not programmed with D-series P-commands, and it is not supported by the Home Assistant ness_alarm integration.

6. What this forum is not covering as "a Ness alarm panel"
Ness also lists products such as the Guardian 4G wireless medical-alert and security controller. That is a different product family. This starter set is about the intrusion-alarm control panels above.

I could not find a current official Ness panel called "Ultra" or a current official product called "Ness Connect". Navigator and Saturn are keypads; Ultraprox is a Wiegand reader (part 101-014). If you have a board or app with one of those names, post a photo of the label (cover off only if it is safe and you are authorised to open the housing) and we can try to identify it from the markings.

7. How to identify your panel, in practice
Work from the board and the official manual, not from the colour of the keypad:
  • The main-board label and the inside of the housing — model (DPlus, D8xD, D16xD, D8XCEL, D16XCEL, M1, SmartLiving 505/515/1050L/10100L), part number and firmware or PCB revision.
  • Firmware version on D-series panels. In user or installer program mode, P99999999E (eight 9s) displays the firmware version on the zone LEDs (the manuals' example: version V6.1 flashes 6, then 1). On a Navigator, the iComms manual also notes that the Info button on the main screen can show the D8x/D16x version at the bottom.
  • Serial header. 3-pin (450-185) usually means an older D8x/D16x. 4-pin (450-246) means DPlus, XCEL, or D8x/D16x V8 and later. M1 and SmartLiving use their own buses and ports.
  • Communications hardware. A 4G module and SIM onboard points at XCEL (or at DPlus with the optional 106-985 module fitted). An add-on ethernet brick on the serial header is typically Ness-Bridge / Ness-Bridge Plus, or an IP232 serial-to-ethernet bridge.
  • Keypad family helps with accessories, not with the panel identity. Navigator, Saturn+ and KPX+ are used across DPlus and later D8x/D16x/XCEL. SmartLiving uses Alien / nCode / Concept keypads. M1 has its own keypad range, including a Navigator option in some Ness kits.
If you are unsure, the firmware display and a clear photo of the board label are more useful than "I think it is a D16".

8. What else is in this forum
The other starter threads cover:
  • connecting a D8x/D16x (and what is and is not proven for DPlus and XCEL) to Home Assistant
  • installer programming basics on D-series panels, including factory-default codes, and when the job needs a licensed installer
  • Mezzo, Ness-Bridge, IP232, SMS and back-to-base monitoring (including the ArmorIP / Contact ID issue on XCEL 4G)
Official starting points
Ness Corporation
Ness: About us
Ness: Contact us and branch addresses
Ness DPlus brochure v3 (PDF)
Ness DPlus Installation & Programming Manual, 890-511 Rev 1.12 (PDF)
Ness D8x/D16x Deluxe Installation & Programming Manual, 890-017 Rev 2.5D (PDF)
Ness D8/D16 XCEL 4G Installation & Programming Manual, 890-490 Rev 1.14 (PDF)
Ness M1 Gold 14" kit
Ness M1 Gold control module
Ness M1 Installation Manual Rev 2.2 (PDF)
Ness: Control Panels (includes SmartLiving listings)
Ness SmartLiving brochure (PDF)
Just Smart Homes t=251: security licensing in Australia
Just Smart Homes t=239: electrical compliance

This is not official Ness advice, not a programming manual, and not a claim that every SKU mentioned is still in stock. Panel firmware, kit contents and catalogue listings change. Check the current official manual for your board, or ask Ness or a licensed installer, before you rely on any point in this thread. Researched from official documentation on 22 November 2026 (Australia/Sydney). Please correct anything that has moved on.
Post Reply

Return to “Ness Alarm System Discussion”