Australian split-system control in 2026: Daikin, Mitsubishi, local vs cloud options

Split systems, ducted AC, heat pumps, thermostats and local or cloud control.
Post Reply
User avatar
ZerOne
Site Admin
Posts: 280
Joined: Sun Dec 13, 2020 8:21 am

What this thread is for
How a typical Australian wall-hung split system can appear in a smart home, and how to tell a local path from a cloud path. It is about control and monitoring, not about sizing or installing the air conditioner itself.

Complexity
Adding a supported official integration: beginner to moderate. Any work on refrigerant pipework, outdoor isolators or new mains circuits is licensed trade work.

1. The unit on the wall is not the same as the interface
Most modern splits are controlled by a manufacturer Wi-Fi adapter, a vendor app, and sometimes a local network API. Two homes with "a Daikin" can behave very differently depending on the adapter family.

2. Daikin — official Home Assistant integration
The official Daikin AC integration talks to supported Wi-Fi controller units and can expose climate, sensor and switch entities (mode, temperature, fan, swing, and so on).

The same official page lists hardware that has been confirmed to work, including Australian controllers:
  • BRP072A42, used with the Daikin Mobile Controller app. Confirmed examples on that page include a Cora 2.5 kW FTXM25QVMA, and Alira X models FTXM20YVMA and FTXM60WVMA.
  • BRP072Cxx based units, including Zena devices, are also listed.
  • European BRP069Axx / BRP069Bxx controllers (ONECTA) are documented separately; do not assume an import adapter matches an Australian indoor unit.
Always check your exact indoor model and the official supported-hardware list before buying an adapter. Local discovery is described on that page; treat any unit that only works through a vendor cloud as a different path.

3. Mitsubishi Electric — official MELCloud integrations
Home Assistant has two official integrations, and they are not interchangeable:
  • MELCloud — sign in with a classic MELCloud account.
  • MELCloud Home — for the newer MELCloud Home service.
Both are cloud services. If the internet or the Mitsubishi service is down, this path will not control the unit. That is the main practical difference from a local Daikin API or a wired interface.

4. Local alternatives
  • ESPHome IR Remote Climate can send the same sort of commands as a handheld remote (platforms include daikin and mitsubishi). This is local, but it usually cannot read the indoor unit's true state unless you also receive IR, and it will fight you if someone uses the original remote.
  • ESPHome Mitsubishi CN105 talks to compatible Mitsubishi indoor units over the CN105 UART (official docs: 2400 baud). This is a more complete local interface, but it is an extra device on the indoor unit's connector. Treat warranty, isolation and wiring as something to confirm with the installer or the interface vendor — do not improvise mains or communications wiring inside the indoor unit.
A worked local ESPHome plus Home Assistant example is in the project thread in this forum.

5. Other Australian systems
Ducted systems, iZone-style zone controllers, and C-Bus or KNX HVAC gateways are different products again. Use the official integration or gateway manual for that brand. The C-Bus and KNX introductions remain the starting points for those buses.

Safety and cost
New adapters that require a licensed electrician or refrigeration technician should be quoted in AUD. Plug-in or manufacturer Wi-Fi modules still need to be compatible and, where they are electrical accessories, appropriately approved. This thread does not quote a single national price.

Official reading
Daikin AC
MELCloud · MELCloud Home
ESPHome IR climate
ESPHome Mitsubishi CN105

Researched from official documentation on 15 November 2026 (Australia/Sydney). This is a planning and how-to guide, not a claim that the exact hardware combination was assembled and tested on a live site. Please correct anything that has moved on.
Post Reply

Return to “Air Conditioning & Climate Control”